Create a Boot Floppy Disk with a Windows XP-Based Computer
1. Format a floppy disk by using the Windows XP format utility. For example, with the floppy disk in the floppy disk drive, type format a: at a command prompt, and then press ENTER.
2. Copy the Ntldr and the Ntdetect.com files from the I386 folder on the Windows XP Setup CD-ROM, Windows XP Setup floppy disk, or from a computer that is running the same version of Windows XP as the computer that you want to access with the boot floppy.
3. Create a Boot.ini file (or copy one from a computer that is running Windows XP), and then modify it to match the computer that you are trying to access. The following example works for a single-partition IDE drive with Windows XP installed in the \Windows folder, but the exact value in the [operating systems] section depends on the configuration of the Windows XP computer that you are trying to access:
2. Copy the Ntldr and the Ntdetect.com files from the I386 folder on the Windows XP Setup CD-ROM, Windows XP Setup floppy disk, or from a computer that is running the same version of Windows XP as the computer that you want to access with the boot floppy.
3. Create a Boot.ini file (or copy one from a computer that is running Windows XP), and then modify it to match the computer that you are trying to access. The following example works for a single-partition IDE drive with Windows XP installed in the \Windows folder, but the exact value in the [operating systems] section depends on the configuration of the Windows XP computer that you are trying to access:
[boot loader]
timeout=30
Default= multi(0)disk(0)rdisk(0)partition(1)\windows
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\windows="Windows XP"
If your computer boots from a SCSI hard drive, you may need to replace the multi(0) entry with scsi(0). If you are using scsi(x) in the Boot.ini file, copy the correct device driver for the SCSI controller in use on the computer to the root of the Setup disk, and then rename it Ntbootdd.sys. Change the disk(0) number to represent the SCSI-ID of the hard drive you want to boot to. If you are using multi(x) in the Boot.ini file, you do not need to do this.
4. Start your computer by using the floppy disk, and then log on to Windows XP.
4. Start your computer by using the floppy disk, and then log on to Windows XP.
Create a Boot Floppy Disk Without a Windows XP-Based Computer
1. Refer to the article Q310994 for directions to download and create the Windows XP Setup disks by using a computer that is running Microsoft Windows 95, Microsoft Windows 98, Microsoft Windows 98 Second Edition (SE), or Microsoft Windows Millennium Edition (Me):
310994 (http://support.microsoft.com/kb/310994/EN-US/) Obtaining Windows XP Setup Boot Disks
2. Delete all the files from the newly created Setup disk 1.
3. Copy the Ntdetect.com and the Ntldr files from the I386 folder on the Windows XP CD-ROM to the new disk.
4. Rename the Ntldr file to Setupldr.bin.
5. Create a Boot.ini file. The following example works for a single-partition IDE drive with Windows XP installed in the \Windows folder, but the exact value in the [operating systems] section depends on the configuration of the Windows XP computer that you want to start:
310994 (http://support.microsoft.com/kb/310994/EN-US/) Obtaining Windows XP Setup Boot Disks
2. Delete all the files from the newly created Setup disk 1.
3. Copy the Ntdetect.com and the Ntldr files from the I386 folder on the Windows XP CD-ROM to the new disk.
4. Rename the Ntldr file to Setupldr.bin.
5. Create a Boot.ini file. The following example works for a single-partition IDE drive with Windows XP installed in the \Windows folder, but the exact value in the [operating systems] section depends on the configuration of the Windows XP computer that you want to start:
[boot loader]
timeout=30
Default= multi(0)disk(0)rdisk(0)partition(1)\windows
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\windows="Windows XP"
If your computer starts from a SCSI hard drive, you may need to replace the multi(0) entry with scsi(0). If you are using scsi(x) in the Boot.ini file, copy the correct device driver for the SCSI controller in use on the computer to the root of the setup disk, and then rename it Ntbootdd.sys. Change the disk(0) number to represent the SCSI-ID of the hard drive you want to start to. If you are using multi(x) in the Boot.ini file, you do not need to do this.
6. Start your computer by using the floppy disk, and then log on to Windows XP.
6. Start your computer by using the floppy disk, and then log on to Windows XP.
No comments:
Post a Comment